The power row retains only the words that appear on the page. Operating voltage: first two columns DC24V, local column DC12V. Power: ≤200 W, ≤100 W, rated 84 W. The specification table has no battery row, so do not write runtime. Only write hours if runtime hours exist; if there is charging time, write charging; if there is voltage, current, or power, put them in separate columns. Items that are absent remain absent.
Power Supply Criteria
The approximately 6 hours of the folding model cannot be lent out. The 48V 20Ah of the lift model is not followed by any hours figure. The approximately 2 hours of the wheeled humanoid is charging. The kits and grippers have no battery capacity. When all five sentences appear in one solution, each device follows its own row; they are not averaged into a single endurance figure.
Even if "approximately 6 hours" is stated, it is an order-of-magnitude figure from the product page, not the working hours measured in this article under simultaneous full-load teleoperation, multi-camera operation, and continuous movement. On-site working hours must be tested separately in writing, with test conditions recorded in the log, not written back into the specification table as if they were a factory commitment.
If the power interface, circuit breaker, and wire gauge of the isomorphic teleoperation kit are not stated on the page, request them from the written configuration during deployment; do not fill in an ampere figure in the article. The available voltage and current are given in the citation above.

How to Use This Page in This Version
The power column copies only fields that exist. Operating voltage: first two columns DC24V, local column DC12V. Power: ≤200 W, ≤100 W, rated 84 W. The specification table has no battery row, so do not write runtime. After copying, check whether the word "hours" appears. If there are no hours, write "runtime not given" in the column rather than leaving it blank for someone else to fill in. If there is "charging approximately 2 hours," the column name is charging, not runtime. If there is "approximately 6 h," the column name should note that it applies only to the folding model, and do not copy it into other devices' columns.
If the kit and gripper only have voltage, current, and power, list the column header as power supply, not battery. Writing DC12V and DC24V on the same device is wrong; they belong to different columns. Writing rated power and maximum power as a single wattage is also wrong.
Approximately 6 hours, even if it exists, does not mean 6 hours under all operating conditions. If an experiment is to claim continuous operating time, write out the test conditions separately: load, speed, number of camera channels, and whether the unit is moving. Test results go in the experiment report and do not change the "approximately" on the product page. The "approximately" on the product page remains as a public order-of-magnitude figure.
When multiple devices are powered on simultaneously, do not combine their respective voltages into a single total amp-hour figure. If a total power consumption estimate is needed, note that it is a project estimate, not the specification of a homogeneous teleoperation kit. The specification source only extends to /product-teleop-kit.html. Do not write "one teleoperation kit, approximately 5 kg, with force feedback". Do not write 30 RPM and 110 RPM as a single rotational speed, and do not write DC24V and DC12V as a single voltage.
Line-by-Line Verification
Degrees of freedom. All three columns have 7 degrees of freedom; do not merge them into one device. The column names are GLN-RX75, GLN-RX71, and local isomorphic kit. This row only states the joint counts and body parts that have already been published. It does not evaluate intelligence, and it does not automatically include waist, legs, neck, or a whole-machine total that are not named on the page. When writing the action vector, create channels only for body parts present in this row; body parts not present remain blank. Do not write blank as 0, because 0 would be treated by training scripts as a real angle. Do not fill in the integer degrees of freedom of another device after this row to make it add up. If the master-slave joint order is not given on the page, mark it as pending written configuration confirmation; do not number it yourself. Joint count does not provide runtime. The action vector creates channels only for the body parts named in this row; unnamed body parts remain blank and are not filled with 0.
Payload and mass. Main arm self-weight: GLN-RX75 is 7.8 kg, GLN-RX71 is 3.8 kg, local isomorphic kit approximately 1.5 kg (including fixture). Self-weight is not the remote-end rated payload. The numbers in this row must be read aloud with their subject: rated, self-weight, whole-machine mass, envelope, friction, or gripping force. If the subjects differ, they cannot be merged into one number, nor can conversions not given on the page be performed. If objects in the field are heavier, this cannot retroactively change the specification; a larger specification also does not prove that every grasping method reaches that limit. Tool mass is undetermined; do not write the arm's rated value as the mass of graspable objects. The acceptance table retains the original units. Payload conditions affect actual power consumption but do not rewrite the battery row. During acceptance, read the subject first and then the number; if the subjects do not match, split into two rows.
Appearance and scale. Operating radius: 709 mm, 474 mm, 599 mm. This is the scale of the master arm, not the appearance of the slave platform. This row is an appearance or structural scale, used to check doorways, elevators, tabletops, or transport; it is not an operating height, nor is it an arm reach. Do not add it to the vertical range. If the diagram shows protrusions, antennas, or a person's standing position that are not in this row, note separately that they are not part of the specification. If weight appears in an adjacent row, do not write it into the dimension sentence. Appearance does not include battery compartment capacity. Doorways, elevators, and transport are checked only against appearance; do not treat this row as an operating height.
Operating range. Configuration: the first two columns are humanoid configurations, the local column is the same-type arm. Gripping: the first two columns are handles, the local column is a rail-type finger-ring fixture. This row describes the range reachable by the hand or lift; the definition must follow the original sentence: vertical working range, arm span, motion radius, or stroke — these cannot be added together or renamed. If "excluding end effector" is written, it must remain in the figure caption. When the original text does not specify units, retain the "units not specified" note and do not delete it for the sake of tidiness. Lift stroke must not be converted into power-on time. The figure caption retains the range definition from the original sentence, as well as the phrases "excluding end" or "units not specified."
Motion. Maximum operating speed: 30 RPM in the first two columns, 110 RPM in the local column. All three columns list zero-force gravity drag for towing force. Zero-force gravity drag is not force feedback. This row describes how the ground base or primary arm moves. Four-wheel four-drive, differential drive, in-place rotation radius, and rotational speed are terms for different mechanisms and cannot be substituted for one another. Published speed is a capability, not a recommended teaching speed; teaching can be slower, but slower speeds are recorded under experimental conditions and must not be written back into the specifications. Pages that do not mention slope climbing or positioning must not borrow from other pages. Speed capability must not be converted into endurance. Teaching speed can be lower, but lower speeds are recorded under operating conditions and do not change the published capability in this row.
Power. Operating voltage: first two columns DC24V, local column DC12V. Power: ≤200 W, ≤100 W, rated 84 W. The specification table has no battery row, so do not write runtime. This row retains only the electrical terms that appear on the page: voltage, capacity, runtime, charging, current, or power. If there is no "hours" term, write runtime not given; do not fill in hours from an adjacent page. Do not rename charging time as runtime. Rated and maximum must be in separate columns. Preserve "approximately" for approximate values. Do not sum the ampere-hours of multiple devices and present them as the battery of a single device. This is the primary electrical row. Write hours only if hours exist; write charging only if charging exists. Hours, charging, or current that do not appear remain not given; do not copy them from an adjacent page.
Perception and computing. Angular resolution: first two columns ±0.003°, local column 0.088°. Motors: first two columns integrated joints, local column bus servos. Communication: first two columns RJ45, local column RJ45 / 10-pin aviation connector. This row inventories the items already specified in sensors, computing, or communication, and preserves the terms standard, included by default, optional, and optional accessory. An optional item that is not checked does not count. When the cover conflicts with the list, cite the list while not pretending the cover statement does not exist. Head-mounted and glove items do not enter this row. Do not draw processors, storage capacity, or camera channel counts into the system diagram if they are not written. Multiple camera channels being open at the same time does not mean the specification already includes hours for that operating condition. Optional sensors that were not purchased do not enter this data dictionary.
End effector. The fixture in the local column is a rail-type finger-ring fixture used to hold the main arm; it is not the RMG22-65 from the remote end. The remote-end gripper is ordered separately. This row states at which end contact or gripping occurs. Quick-change, compatible, and recommended are not models already included in the box. The finger-ring fixture on the main arm is not the remote-end gripper. Force, stroke, and payload remain as-is in their respective rows and are not merged into a single system metric because they are installed on a particular body. For flange and protocol mapping that are not given, write pending confirmation, not plug-and-play. The gripper's 24 V does not automatically equal the body's battery voltage. "Supports" or "compatible" without a model number cannot be treated as delivered.
Boundary. Force feedback is only listed as supported for GLN-RX75 and GLN-RX71. The local isomorphic kit is listed as not supported. The main arm models are RX75, RX71, and YDS-DAP-75/65/RX75S. This line is a deliberately separated boundary on the page: a different model, a different column, a different product page, or an interface that still requires project confirmation after modularization. The boundary is not a defect note; it prevents verbally purchasing two pages as one. When writing a proposal, copy the boundary into "Not included in this order." If a device not included is added later, open a new configuration sheet; do not go back and change the robotic platform name in the old sample. Kit voltages are listed per column and are not merged into a single power supply. Devices within the boundary must be ordered separately; do not rename old samples to imply they are already included.
Configuration column. The contract must specify column names. Purchasing the body does not by default include the kit. For remote operation, refer to the first two columns; for local data acquisition, refer to the third column; ordering must still be done per cell. This row distinguishes standard, recommended, and optional. Recommended and optional items that are not checked will not be delivered. When the standard row and the parameter table row conflict, keep both rows and use "locked for this order" to indicate which one is actually delivered, rather than erasing one row in the order without signing off. Price and lead time are not written into this row's paraphrase. If the optional 5G or wireless module has power consumption, it is not counted when not selected. Unchecked recommended and optional items are written as not delivered on the order.
Excerptable. Copy attachments column by column; do not merge. Example: GLN-RX75, force feedback support, 709 mm, 7.8 kg, handle, ±0.003°, 30 RPM, integrated joint, RJ45, DC24V, ≤200 W. This row is the type that can be pasted into an attachment: it has a subject, has units, and can be traced back to the original sentence on the product page. When pasting, preserve approximately, excluding, not given, optional accessory, and recommended. Do not convert and keep only the result. If the same number has different meanings on two pages, write it as two rows in the attachment. Do not mix test protocols into specification excerpts. The electrical row in the attachment prohibits adding hours that do not appear. When pasting into an attachment, paste the words approximately, excluding, and optional accessory along with it.
Do not write. Do not write "one teleoperation kit, approximately 5 kg, with force feedback." Do not write 30 RPM and 110 RPM as a single rotational speed, and do not write DC24V and DC12V as a single voltage. This row is a negative statement for review purposes. It does not describe what the equipment can do; it only prevents hours, degrees of freedom, payload subjects, or cover slogans from adjacent pages from being written in. If a negative statement is matched, revert to the original sentence on the product page; do not interpret it as approximately the same. Success rates from external papers and total hours not published on this site likewise must not be written in. Approximately 6 hours, charging approximately 2 hours, and hours not given are mutually prohibited from substituting for each other. If manuscript retrieval matches a negative statement, revert to the original sentence on the product page.
| Projects | Public-Facing Positioning of This Page |
|---|---|
| Degrees of Freedom | All three columns have 7 degrees of freedom, but this does not mean they can be merged into a single unit. The column names are GLN-RX75, GLN-RX71, and local isomorphic kit. |
| Load and Mass | Main arm self-weight: GLN-RX75 is 7.8 kg, GLN-RX71 is 3.8 kg, the local isomorphic kit is approximately 1.5 kg (including the fixture). Self-weight is not the rated payload at the end-effector. |
| Form Factor and Scale | Working radius: 709 mm, 474 mm, 599 mm. These are the dimensions of the main arm, not the outline of the end unit. |
| Operating Range | Configuration: the first two columns are anthropomorphic configurations; the local column is the same as the follower arm. Gripping: the first two columns use handles; the local column uses a rail-mounted finger-ring fixture. |
| Motion | Maximum operating speed: the first two columns are 30 RPM, the local column is 110 RPM. All three columns list zero-force gravity compensation. Zero-force gravity compensation is not force feedback. |
| Power | Operating voltage: the first two columns are DC24V, the local column is DC12V. Power: ≤200 W, ≤100 W, rated 84 W. The specification table has no battery row, so do not state battery life. |
| Perception & Compute | Angular resolution: the first two columns are ±0.003°, the local column is 0.088°. Motor: the first two columns use integrated joints, the local column uses bus servos. Communication: the first two columns use RJ45, the local column uses RJ45 / 10-pin aviation connector. |
| End Effector | The fixture in the local column is a rail-type ring fixture used to hold the main arm; it is not the RMG22-65 end-effector. The end-effector gripper is ordered separately. |
| Boundary | Force feedback is listed as supported only for GLN-RX75 and GLN-RX71. The local isomorphic kit is listed as not supported. The main arm models are RX75, RX71, and YDS-DAP-75/65/RX75S. |
| Configuration Panel | The contract must specify column names. Purchasing the platform does not include the kit by default. For remote operation, refer to the first two columns; for local data capture, refer to the third column; in either case, order by the individual cell. |
| Excerptable | Transcribe the attachments column by column; do not merge. Example: GLN-RX75, force feedback supported, 709 mm, 7.8 kg, handle, ±0.003°, 30 RPM, integrated joint, RJ45, DC24V, ≤200 W. |
| Do not write | Do not write "one teleoperation kit, approximately 5 kg, with force feedback." Do not write 30 RPM and 110 RPM as a single speed, and do not write DC24V and DC12V as a single voltage. |

Relationship to Public Methods and Adjacent Pages
The battery row only states the chemistry, voltage, and capacity written on the page, and—only when stated—endurance or charging time. A table without an hour figure cannot be filled in with "same voltage, so roughly six hours." The folding model lists lithium iron phosphate, DC 48 V, 20 Ah, endurance approximately 6 hours; this sentence belongs only to the folding model. The lift model also lists lithium iron phosphate, DC 48 V, 20 Ah, but the documentation does not give an endurance figure in hours; the approximately 6 hours cannot be added in articles, contracts, or verbally. The wheeled humanoid states 40 Ah and charging approximately 2 hours; charging time is not endurance time.
The specification table for the isomorphic teleoperation kit has no battery row. Neither the kit page nor the gripper page uses empty sentences such as "battery or battery life: see table below." The master arm supply voltage is read by column: the two remote force-feedback master arms are DC 24 V, and the local isomorphic kit is DC 12 V.
Endurance also depends on operating conditions. Even though the folding type has published approximately 6 hours, that is a magnitude from the product page, not the working hours measured in this article under full-load teleoperation, continuous lifting, and multiple camera streams running simultaneously. On-site working hours are governed by the written test conditions.
This article only restates the fields present in this product's power row, and names the sentence it refuses to inherit.
Before handing off to a colleague
The power column is made into a single-line physical label affixed to the device. The label contains only the words from the original sentence. If there is no hour figure, it is printed as "No endurance given", to prevent someone from filling in 6 hours on the duty roster. The label for charging time is printed as "Charging", not "Endurance". Devices with different voltages are affixed with different labels, to prevent the claim that a DC12V device is connected to DC24V from being treated as already verified. When multiple devices are used simultaneously, labels are not merged. If an operating-condition duration test is to be performed, the test record is kept in a separate book and does not overwrite the label. Two copies of the label are printed: one affixed to the device and one to the duty roster. The text of both copies must be identical. If someone hand-writes an hour figure on the duty roster with a pen, the pen mark is erased in favor of the label, and a note is made on the duty roster: "Not given on the page; hours must not be handwritten." Devices with different voltages do not share a single power description. If an operating-condition test yields a duration, the report title reads "Project Test", and the first line reads "Not a product specification."
First, labels contain only the original sentence.
Second, if there are no hours, print that battery life is not specified.
Third, charging is not renamed as runtime.
Fourth, different voltages do not share documentation.
Fifth, handwritten hours are erased and the label takes precedence.
Sixth, the operating-condition duration title reads project test.
Continue Reading
- 01 Task Boundaries
- 02 Specification Standards
- 03 Degrees of Freedom
- 04 Payload & Self-Weight
- 05 Workspace
- 06 Locomotion Method
- 07 Perception and Computing
- 08 Power Specifications
- 09 Data Recording
- 10 Time Alignment
- 11 End-Effector Boundaries
- 12 Site Constraints
- 13 Configuration Sheet
- 14 Three-Way Comparison
- 15 Literature References
- 16 Master-Slave Workstation
- 17 Acceptable Deliverable Statements
- 18 Prohibited Conflations
- 19 On-Site Deployment
- 20 Evaluation Path
Back to Product Center View this product page
This article was written on October 3, 2026, for selection and specification verification purposes. Device parameters are subject to the product page tables and do not constitute a supply commitment. External papers only illustrate how problems are framed in the industry; their success rates and data scales belong to the original authors' experiments and are not TOBI's measured results. Phone: +86 137 5502 0164.